Beginner's Plumbing: What You Need for Installing a Bathtub
Click HereWe have stumbled upon this article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the net and felt it made sense to write about it with you on my blog.
Installing a tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is conveniently accessible, the job can move rapidly; if you have to open up a wall to eliminate the old bathtub and also position the brand-new tub, the task is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Make sure you have certified on your own for the task as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed job, it is far better to consider employing one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This article will certainly aid you install a new bath tub in your restroom if you have actually currently bought a new bathtub and don't require to change the setup of your previous water pipes.
Your devices and also material checklist need to comprise the following:
Planning for the Setup
Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to stop pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be quite problematic due to the restricted gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this procedure. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, place the bathtub in the required placement. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four small points.
The following objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the water as well as examine all joints and also brand-new pipework for leakages and tighten them if required. Fill up the bath tub and also check the overflow outlet and also the normal outlet for leakages.
Ultimately, deal with the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub needs to wait up until the bathtub has been utilized at least once as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Safeguard the faucet in position with the supplier given backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type should be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to fracture a rigid seal, triggering the water to permeate the wall surface between the bath as well as the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes and also cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can crack rather very early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our topic about Tools You Need to Install a New Bathtub . Thanks so much for finding the time to browse our blog post. I beg you take the opportunity to share this write-up if you appreciated it. Thank you so much for your time invested reading it.
High-quality, fast plumbing repairs.